Gas Turbine Intake Air Filter For Gas Turbine GE
  • Gas Turbine Intake Air Filter For Gas Turbine GEGas Turbine Intake Air Filter For Gas Turbine GE

Gas Turbine Intake Air Filter For Gas Turbine GE

The JinJue Gas Turbine Intake Air Filter For Gas Turbine GE is an indispensable component of the gas turbine system, widely used in various fields such as power generation, aviation, and industry. Its main task is to filter out particulate matter and pollutants from the air before it enters the gas turbine engine.

Send Inquiry

Product Description

JinJue Gas Turbine Intake Air Filter For Gas Turbine GE play a crucial role in protecting turbine components, enhancing filtration efficiency, reducing pressure drop, providing pre-filtration options, and ensuring regular maintenance. Proper use and maintenance of these filters can significantly improve system performance, lower maintenance costs, and extend equipment lifespan, ensuring reliability and efficiency across various industries.

Product Features:

1.Contaminant removal
3.Pressure drop
4.Pre-filtration and coalescing stages (optional)
Properly maintained intake air filters play a crucial role in optimizing the gas turbine's performance, reducing maintenance costs, and extending its operational life. They are a critical aspect of ensuring the long-term reliability and efficiency of gas turbine systems across various industries.

Detailed information:

Name of Item or Related Service Technical Specification and Standards
Gas Turbine Intake Air Filter For Gas Turbine GE(Cylindrical and Conical) For Gas Turbine GE Filter media:100% Synthetic nonwoven water repellent composite media.
Pleats:Pleats are to be stabilized spiral by hot-melt adhesive on both inner and outer cores.
No of Pleats and Media Area:No of pleats for cylindrical: ≥310 pleats Media Area for cylindrical: ≥18 m2 No of pleats for conical: ≥375 pleats Media Area for conical: ≥22 m2
End caps:Galvanized
Open Liners (Inner & Outer):Galvanized carbon steel G90 to ASTM653 or greater
Construction:Full metallic Construction, Non-welded
Washer:Each filter set should be provided with 1 pc of standard Rubber coated washer for setting filter set on the tripod.
Gasket material:Single piece, seamless, skinned foam in place polyurethane (closed cell) or EPDM.
Gasket stops:Integrated into the conical filter preventing over compression of the gasket. Polyurethane foam shall be consistency that when 6-10FT-LBS of tightening on retention bolt, seal will be tight as to allow no dirty air by-pass.
Glue/Potting type:Polyurethane
Dimensions: Cylindrical:OD of Cap: Ø324 ID of Cap: Ø215Hole of ID Close End Cap: Ø30mm Length:660 Conical:Smaller End Cap OD: Ø324 Smaller End Cap ID: Ø215 Larger End Cap OD: Ø445 Larger End Cap ID: Ø330 Length: 660Note 1: Tolerance in Dimension ±3mmNote 2: Cylindrical + 1 Conical= 1Set and Outer dimension of Cylindrical should be same to the smaller end of Conical.
Weight:Cylindrical:Must not exceed 6kg cleanConical:Must not exceed 7kg clean
Air Flow Rate:2338m3/hr to 2980 m3/hr
Average Efficiency for 0.4 µm particles:≥95%(Test certificate required, tested by independent test house)
Efficiency Class:a) EN779:2012: F9(Test certificate should be submitted, tested by independent test house)
Dust holding capacity:≥2000g at a pressure drop of 4” WG(1000 Pa) using ASHRAE test dust:
Initial pressure drop at >2338m3/hr:<240Pa (0.96’’H2O)
Burst pressure, in both wet and dry condition:>6230PA (25’’H2O)
Humidity Range:0 to 100% relative humidity
Operation temperature range:-40 degrees C to +50 degrees C(-40°F to +122°F)

Product Details

Hot Tags: Gas Turbine Intake Air Filter For Gas Turbine GE, China, Manufacturer, Supplier, Factory, High Quality

Related Category

Send Inquiry

Please Feel free to give your inquiry in the form below. We will reply you in 24 hours.

Related Products

We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
Reject Accept